National Loop Co. 48' (6' X 18') Saw Cut Vehicle Detection Loop with 250' Lead-In for 24' Wide Driveways - P-NL24-18-250

National Loop Co. 48' (6' X 18') Saw Cut Vehicle Detection Loop with 250' Lead-In for 24' Wide Driveways - P-NL24-18-250

The National Loop Co. 48' Saw Cut Vehicle Detection Loop with 250' Lead-In triggers automatic gate operation the second a vehicle rolls over the wire. The signal gives the gate system one of the two means of entrapment protection required by UL 325, a must for safe automatic operation. Crews cut a narrow channel in the existing driveway, set the factory-wound loop inside, and seal it against moisture. Its footprint of 6' x 18' yields 48' of 18 AWG wire, sized to 24' wide driveways such as church lots, small office entries, and 2-car-plus-walkway drives.
Part Number: P-NL24-18-250
$244.46 each $244.46 each
OR
 

Details

National Loop Co. 48' (6' X 18') Saw Cut Vehicle Detection Loop with 250' Lead-In for 24' Wide Driveways - P-NL24-18-250

Designed to sense vehicles without any surface teardown, the National Loop Co. 48' Saw Cut Vehicle Detection Loop with 250' Lead-In is a preformed 18 AWG loop that drops into a saw-cut slot. Wired to compatible automated system, the loop counts as one of the two means of entrapment protection UL 325 requires for gate operators, detecting the metal of any vehicle over the sensing area so the gate stops or reverses before contact. Installers saw a 1/8" by 1" deep slot into the existing surface, drop the prewound loop in, and seal the slot against moisture. With the 18' side crossing the lane and about 3' of clearance per edge, and the 6' side capturing vehicles in the direction of travel, the layout fits 2-car plus full walkway and church or small office lot entries.

Features:

  • Works wherever vehicles need detecting: automatic gates, parking barriers, overhead doors, traffic signals, arming devices, and vehicle counters
  • One continuous, non-spliced Polypropylene-insulated wire runs through the loop turns and lead-in, eliminating splice failures
  • Factory-set turn count means optimal read range without any on-site adjustment
  • Precisely stacked wires let loop sealant fully encapsulate the loop for lasting weather protection
  • Cuts down on faulty detection calls and repeat service trips thanks to consistent machine winding
  • More cost-effective than hand-wound loop installations
  • Fills the non-contact detection role UL 325 assigns to vehicle loops in a 2-device entrapment protection system

Specifications:

  • Loop type: Saw cut
  • Total loop length: 48'
  • Loop dimensions: 6' x 18'
  • Lead-in length: 250'
  • Slot size: 1/8" wide x 1" deep
  • Wire gauge: 18 AWG
  • Wire material: Polypropylene-wrapped copper wire
  • Best-suited driveway width: 24'
  • Manufacturer: National Loop Company (NLC)
  • Made in America: Yes
Prefer to Call? (888) 378-1175

Questions about part number P-NL24-18-250?

Required Fields *

Name *

Email *

Phone

My Questions *

Loop Type Saw Cut
Lead-In Length 250'
Loop Length Size 6' X 18'
Total Loop Length 48'
Wire Size 1/8"
SKU P-NL24-18-250
Product Type Saw Cut Preformed Loop
Made In America Tooltip
Learn More About BABA Certification
Yes
Ideal Application Access Control, Arming Devices, Gate Operators, Overhead Doors, Parking Barrier Gates, Traffic Signals, Vehicle Counters
Material Polypropylene-Wrapped Copper Wires
Manufacturer National Loop Company - NLC
Specification Sheet Download PDF file